PC Software -V1
HV BMS Software new version-TOPBMS.zip
HV BMS-PC Software old version-TOPBMS.zip
BMS Basic protocals
BMS CAN Protocals == Basic Information of BMS only.xls
English Version of User Manual
1 - Master BMS (BMC) User Manual -English.pdf
2 - Slave BMS (BIC) User Manual - English.pdf
3 - PCC-M0810 User Manual - English.pdf
5 -DISPLAY User Manual -English.pdf
6 - GBT Charger Adaptor -CCM-M0805 - English.pdf
BMS CAN Protocals
CAN Protocals of BMS BASIC INFO.xls
How to Configurate BMS in PC Software, Please see below :
1-BMS Configuration - English Version.pdf
2 - BMS wake-up and working strategy-English Version.pdf
3 -BMS Manual (BMSconnectedtoPCviaUSBconnection) - English Version.pdf
4.The WiFi module of HC-25 solution is set for on-sitedirectconnection - English Version.pdf
5.WiFi module of HC-25 solution configured for remote monitoring -English Version.pdf
Wiring Diagrm
How to wake up the master bms (BMC)?
Supply 12V to C6 and GND to wake up BMC ;
Points of CANbus wires connections between master bms and slave bms
only 2 pcs 120ohm resistor shall be installed at the end of each canbus
The same to external devices ，such as display ,charger ; you need to add one resistor 120ohm/1W to external device ,one resistor 120ohm/1W to Master BMS
How to set the address slave bms ? Please see below
if you set on master bms , you need to hold pressing the button of master bms only
and then go to the pcsoftware to do setting
if you set on slave bms , you need to hold pressing the button of master bms and slave bms
and then go to the pcsoftware to do setting
How to set the bms work current range ? Please see below:
First of all , please select BMC-0811(40mV) and then enter the sensor output value of shunt and finally ,please click the button "Calibration"; you will get the bms current range
Nornally the BMS can work under this range 0-400V ; if the working condition
of bms is > 400V , you need to expand the bms working voltage range
How to expand BMS work Voltage Measurement Range,please see below
总电压检测标定实例：电池组3.2V*192串，最高总电压3.6*192=691.2V，超过了BMC默认的约400V量程，需要扩展总电压量程。每扩展100V大约需要串联200K的电阻。选择820K/1W电阻串联到总电压检测的信号线中。软件中扩展电阻输入820，Ra、Rb不改动。点击标定，软件提示“Done”。读取总电压量程，显示815V，满足最高电压值的测量。
Take example of Total voltage measurement and calibration : Battery pack 3.2V*192 in series, the maximum total voltage 3.6*192=691.2V, exceeds the measurement range of about 400V of the master bms , It need to expand the total voltage range. Approximately 200K resistance in series is required for every 100V extension. Select 820K/1W resistors connected in series to the signal wire for total voltage measurement. For the expanded resistance ,enter 820 in the PC software, Ra, Rb remain unchanged. Click " Calibration", and the software shows "Done". Read the total voltage range, showing 815V, to be in line with the highest voltage
How to connect bms + GBT fast DC charger communication ？ Please see below
Note : This bms can work with China National DC fast charger under CAN communication Protocals
BMS CAN Protocals :
CAN Protocals of BMS BASIC INFO.xls
Charger Protocal Standard : GBT27930-2015
GBT27930-2015 Charger Protocals -EN.pdf
How to connect master bms + TC OBC charger /SMT OBC charger ? Please see below
How to connect TOUCHABLE DISPLAY to master bms ? Pease see below :
Please take display to this port of BMC:
How to use wifi mode? you can control bms via local control or remote control ;
How to set the working mode of PCC and BMS wake-up ? You can do it as below
